E2EM-X30MX1 Proximity Switch NEW

E2EM-X30MX1 OMRON Proximity Switch NEW

Product Description:

Long-distance detection at up to 30 mm enables secure mounting with reduced problems due to workpiece collisions.

No polarity for easy wiring with DC 2-wire models.

Cable protector provided as a standard feature.

Specifications:

Size		M12	M18		M30
Shielded		Shielded	Shielded	Unshielded	Shielded	Unshielded
Model		E2EM-X4X[]	E2EM-X8X[]	E2EM-X16MX[]	E2EM-X15X[]	E2EM-X30MX[]
Sensing distance		4 mm ±10%	8 mm ±10%	16 mm ±10%	15 mm ±10%	30 mm ±10%
Set distance *1		0 to 3.2 mm	0 to 6.4 mm	0 to 12.8 mm	0 to 12 mm	0 to 24 mm
Differential travel		15% max. of sensing distance
Detectable object		Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Datasheet.)
Standard sensing object		Iron, 12 × 12 × 1 mm	Iron, 18 × 18 × 1 mm	Iron, 45 × 45 × 1 mm	Iron, 30 × 30 × 1 mm	Iron, 70 × 70 × 1 mm
Response frequency *2		1 kHz	0.5 kHz	0.4 kHz	0.25 kHz	0.1 kHz
Power supply voltage		12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
(operating voltage range)
Leakage current		0.8 mA max.
Control	Load	3 to 100 mA
output	current
	Residual	5 V max. (Load current: 100 mA, Cable length: 2 m)
	voltage *3
Indicators		X1 Models: Operation indicator (red), Setting indicator (green)
		X2 Models: Operation indicator (red)
Operation mode		X1 Models: NO
(with sensing object		X2 Models: NC
approaching)		Refer to Datasheet.
Protection circuits		Surge suppressor, Load short-circuit protection
Ambient temperature range		Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range		Operating/Storage: 35% to 95% (with no condensation)
Temperature influence		±15% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence		±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance		50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength		1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance		Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance		Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection		IEC 60529 IP67, in-house standards: oil-resistant
Connection method		Pre-wired Models (Standard cable length: 2 m)
Weight (packed state)		Approx. 60 g	Approx. 130 g	Approx. 150 g	Approx. 180 g	Approx. 210 g
Materials	Case	Nickel-plated brass
	Sensing	PBT
	surface
	Clamping	Nickel-plated brass
	nuts
	Toothed	Zinc-plated iron
	washer
Accessories		Instruction manual

*1.Use the Sensor within the range in which the setting indicator (green LED) is ON (except X2 Models).

*2.The response frequency is an average value.

Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.

*3.The residual voltage is 5 V. Make sure that the device connected to the Sensor can withstand the residual voltage. (Refer to Datasheet.)