H3DK-M2 AC/DC24-240 Time Relay NEW

H3DK-M2 AC?DC24-240 OMRON Time Relay NEW

OMRON Time Relay H3DK-M2 AC?DC24-240             

Product Description:

Multiple time ranges and operating modes let you cover a wide range of applications.

The time-limit DPDT output contacts can be changed to time-limit SPDT and instantaneous SPDT output contacts using a switch.

Sequence checks are easily performed by setting an instantaneous output to 0.

Start signal control for the H3DK-M.

Specifications:

Ratings
Power supply voltage *1		24 to 240 VAC/DC, 50/60 Hz *2
		12 VDC *2
Allowable voltage fluctuation		24 to 240 VAC/DC: 85% to 110% of rated voltage
range		12 VDC: 90% to 110% of rated voltage
Power reset		Minimum power-OFF time: 0.1 s
Reset voltage		10% of rated voltage
Voltage input		24 to 240 VAC/DC
		High level: 20.4 to 264 VAC/DC, Low level: 0 to 2.4 VAC/DC
		12 VDC
		High level: 10.8 to 13.2 VDC, Low level: 0 to 1.2 VDC
Power	H3DK-M2/-S2	At 240 VAC: 6.6 VA max. *4
consumption	H3DK-M1/-S1	At 240 VAC: 4.5 VA max. *4
*3	H3DK-M2A/-S2A	At 12 VDC: 0.9 W max.
	H3DK-M1A/-S1A	At 12 VDC: 0.6 W max.
Control output		Contact output, 5 A at 250 VAC with resistive load (cosΦ = 1), 5 A at 30 VDC with resistive load *4, *5
Ambient operating temperature		-20 to 55°C (with no icing)
Storage temperature		-40 to 70°C (with no icing)
Ambient operating humidity		25% to 85%

*1.When using a 24-VDC power supply voltage, there will be an inrush current of approximately 0.25 A. Allow for this inrush current when turning ON and OFF the power supply to the Timer with device with a solid-state output, such as a sensor.

*2.DC ripple: 20% max.

*3.The power consumption is for mode A after the Timer times out.

For the H3DK-M[], the maximum power consumption is given, including the current consumed by the input circuit.

*4.Refer to DC Power Consumptions (Reference Information) on Data Sheet for DC power consumptions.

*5.The control output ratings are for one H3DK operating alone. If you operate two or more Timers side by side, refer to Installation Pitch and Output Switching Capacity (Reference Values) in the below.

*6.125 VDC: 0.15 A max. with resistive load, 125 VDC: 0.1 A with L/R of 7 ms.

Minimum load: 10 mA at 5 VDC (P level, reference value)

Characteristics
Accuracy of operating time		±1% of FS max. (±1% ±10 ms max. at 1.2-s range) *
Setting error		±10% of FS ±0.05 s max. *
Minimum input signal width		50 ms* (start input)
Influence of voltage		±0.5% of FS max. (±0.5% ±10 ms max. at 1.2-s range)
Influence of temperature		±2% of FS max. (±2% ±10 ms max. at 1.2-s range)
Insulation resistance		100 MΩ min. at 500 VDC
Dielectric strength		Between current-carrying metal parts and exposed non-current-carrying metal parts: 2,000 VAC
		50/60 Hz for 1 min.
		Between control output terminals and operating circuit: 2,000 VAC 50/60 Hz for 1 min.
		Between contacts not located next to each other: 1,000 VAC 50/60 Hz for 1 min.
Impulse withstand voltage		24 to 240 VAC/VDC: 3 kV between power terminals, 4.5 kV between current-carrying metal parts and
		exposed non-current-carrying metal parts
		12 VDC: 1 kV between power terminals, 1.5 kV between current-carrying metal parts and exposed non-
		current-carrying metal parts
Noise immunity		Square-wave noise generated by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise): ±1.5 kV
Static immunity		Malfunction: 4 kV, Destruction: 8 kV
Vibration	Destruction	0.75-mm single amplitude at 10 to 55 Hz for 2 h each in 3 directions
resistance	Malfunction	0.5-mm single amplitude at 10 to 55 Hz for 10 min each in 3 directions
Shock	Destruction	1,000 m/s2 3 times each in 6 directions
resistance	Malfunction	100 m/s2 3 times each in 6 directions
Life	Mechanical	10 million operations min. (under no load at 1,800 operations/h)
expectancy	Electrical	100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h)
Degree of protection		IP30 (Terminal block: IP20)
Weight		Approx. 120 g