H3CR-A8 AC100-240V Time Relay NEW

H3CR-A8 AC100-240V OMRON Time Relay NEW

OMRON Time Relay H3CR-A8 AC100-240V

Product Description:

A wide AC/DC power supply range greatly reduces the number of timer models kept in stock.

A wide range of applications with multiple operating modes, six modes for 11-pin models and four modes for 8-pin models.

Ecological design with reduced current consumption.

Easy sequence checking with instantaneous outputs for a zero set value.

Length of 80 mm or less when panel-mounted with a P3GA-11 Socket (H3CR-A8E, 100 to 240 VAC, 100 to 125 VDC)

PNP input models available.

Standards: UL, CSA, NK, LR, EN 61812-1, and CE Marking.

Specifications:

General
Item	H3CR-A/-AS	H3CR-AP	H3CR-A8/-A8S	H3CR-A8E
Operating mode	A: ON-delay		A: ON-delay (power supply start)
	B: Flicker OFF start		B2: Flicker ON start (power supply start)
	B2: Flicker ON start		E: Interval (power supply start)
	C: Signal ON/OFF-delay		J: One-shot (power supply start)
	D: Signal OFF-delay
	E: Interval
	G: Signal ON/OFF-delay (Only for H3CR-A-300)
	J: One-shot (Only for H3CR-A-300)
Pin type	11-pin		8-pin
Input type	No-voltage input	Voltage input	---
Time-limit	H3CR-A/-A8/-AP: Relay output (DPDT)			Relay output (SPDT)
output type	H3CR-AS/-A8S: Transistor output (NPN/PNP universal)*
Instantaneous	---			Relay output (SPDT)
output type
Mounting method	DIN track mounting, surface mounting, and flush mounting
Approved standards	UL508, CSA C22.2 No.14, NK, Lloyds
	Conforms to EN61812-1 and IEC60664-1 (VDE0110) 4kV/2.
	Output category according to EN60947-5-1 for Timers with Contact Outputs.
	Output category according to EN60947-5-2 for Timers with Transistor Outputs.

*The internal circuits are optically isolated from the output. This enables universal application as NPN or PNP transistor.

Standard (0.05-s to 300-h) Models
Time unit		s (sec)	min (min)	h (hrs)	×10 h (10 hrs)
Full scale setting	1.2	0.05 to 1.2	0.12 to 1.2		1.2 to 12
	3	0.3 to 3			3 to 30
	12	1.2 to 12			12 to 120
	30	3 to 30			30 to 300
Double (0.1-s to 600-h) Models
Time unit		s (sec)	min (min)	h (hrs)	×10 h (10 hrs)
Full scale setting	2.4	0.1 to 2.4	0.24 to 2.4		2.4 to 24
	6	0.6 to 6			6 to 60
	24	2.4 to 24			24 to 240
	60	6 to 60			60 to 600

 

Ratings
Rated supply voltage	100 to 240 VAC (50/60 Hz)/100 to 125 VDC,
(See notes 1 and 2.)	24 to 48 VAC (50/60 Hz)/12 to 48 VDC
	(24 to 48 VAC/VDC for H3CR-A8E)
	(See note3.)
Operating voltage range	85% to 110% of rated supply voltage (90% to 110% at 12 VDC)
Power reset	Minimum power-opening time: 0.1 s
Input	No-voltage Input
	ON impedance: 1 kΩ max.
	ON residual voltage: 1 V max.
	OFF impedance: 100 kΩ min.
	Voltage Input
	Max. permissible capacitance between inputs lines (terminals 6 and 7): 1,200 pF
	Load connectable in parallel with inputs (terminals 6 and 7).
	100 to 240 VAC/100 to 125 VDC
	High (logic) level: 85 to 264 VAC/85 to 137.5 VDC
	Low (logic) level: 0 to 10 VAC/0 to 10 VDC
	24 to 48 VAC/12 to 48 VDC
	High (logic) level: 20.4 to 52.8 VAC/10.8 to 52.8 VDC
	Low (logic) level: 0 to 2.4 VAC/0 to 1.2 VDC
Power consumption	H3CR-A/-A8
	100 to 240 VAC/100 to 125 VDC
	(When at 240 VAC, 60 Hz)
	Relay ON: approx. 2.0 VA (1.6 W)
	Relay OFF: approx. 1.3 VA (1.1 W)
	24 to 48 VAC/12 to 48 VDC
	(When at 24 VDC)
	Relay ON: approx. 0.8 W
	Relay OFF: approx. 0.2 W
	H3CR-AP (See note 3)
	100 to 240 VAC/100 to 125 VDC
	(When at 240 VAC, 60 Hz)
	Relay ON: approx. 2.5 VA (2.2 W) (See note 4.)
	Relay OFF: approx. 1.8 VA (1.7 W) (See note 4.)
	24 to 48 VAC/12 to 48 VDC
	(When at 24 VDC)
	Relay ON: approx. 0.9 W (See note 4.)
	Relay OFF: approx. 0.3 W (See note 4.)
	H3CR-A8E
	100 to 240 VAC/100 to 125 VDC
	(When at 240 VAC, 60 Hz)
	Relay ON/OFF: approx. 2 VA (0.9 W)
	24 to 48 VAC/VDC
	(When at 24 VDC)
	Relay ON/OFF: approx. 0.9 W
	H3CR-AS/-A8S
	24 to 48 VAC/12 to 48 VDC
	(When at 24 VDC)
	Output ON: 0.3 W Output OFF: 0.2 W
Control outputs	Time limit contacts: 5 A at 250 VAC/30 VDC, 0.15 A at 125 VDC, resistive load (cosΦ = 1)
	Transistor output: Open collector (NPN/PNP), 100 mA max. at 30 VDC max.,
	residual voltage: 2 V max.
	Instantaneous contact: 5 A at 250 VAC/30 VDC, 0.15 A at 125 VDC, resistive load (cosΦ = 1)

Note:

1.DC ripple rate: 20% max. (A single-phase, full-wave-rectification power supply can be used).

2.Do not use an inverter output as the power supply.

3.Models with 24-to-48-VAC or 12-to-48-VDC power supply have inrush current. Caution is thus required when turning ON and OFF power to the Timer with a non-contact output from a device such as a sensor. (Models with an inrush current of approximately 50 mA and a 24-VDC power supply are available (the H3CR-A-302 and H3CR-A8-302).)

4.The values are for when the terminals 2 and 7 and terminals 10 and 6 are short-circuited, and include the consumption current of the input circuit.

Characteristics
Accuracy of	±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s or 3 s)
operating time
Setting error	±5% FS ±50 ms *1
Reset time	Min. power-opening time: 0.1 s max.
	Min. pulse width: 0.05 s (H3CR-A/-AS)
Reset voltage	10% max. of rated supply voltage
Influence of voltage	±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s or 3 s)
Influence of	±1% FS max. (±1%±10 ms max. in a range of 1.2 s or 3 s)
temperature
Insulation resistance	100 MΩ min. (at 500 VDC)
Dielectric strength	2,000 VAC (1,000 VAC for H3CR-A[]S), 50/60 Hz for 1 min (between current-carrying metal parts and exposed non-current-carrying metal parts)
	2,000 VAC (1,000 VAC for H3CR-A[]S), 50/60 Hz for 1 min (between control output terminals and operating circuit)
	2,000 VAC, 50/60 Hz for 1 min (between contacts of different polarities)
	1,000 VAC, 50/60 Hz for 1 min (between contacts not located next to each other)
	2,000 VAC, 50/60 Hz for 1 min (between input and control output terminals and operation circuit) for H3CR-AP
Impulse withstand	3 kV (between power terminals) for 100 to 240 VAC/100 to 125 VDC, 1 kV for 24 to 48 VAC/12 to 48 VDC
voltage	4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to 240 VAC/100 to 125 VDC, 1.5 kV for 24 to 48 VAC/12 to 48 VDC and 24 to 48 VAC/VDC
Noise immunity	±1.5 kV (between power terminals) and ±600 V (between no-voltage input terminals), square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)
Static immunity	Malfunction: 8 kV
	Destruction: 15 kV
Vibration resistance	Destruction: 10 to 55 Hz with 0.75-mm single amplitude each in 3 directions for 2 hours each
	Malfunction: 10 to 55 Hz with 0.5-mm single amplitude each in 3 directions for 10 minutes each
Shock resistance	Destruction: 1,000 m/s2 3 times each in 6 directions
	Malfunction: 100 m/s2 3 times each in 6 directions
Ambient temperature	Operating: -10°C to 55°C (with no icing)
	Storage: -25°C to 65°C (with no icing)
Ambient humidity	Operating: 35% to 85%
Life expectancy	Mechanical: 20,000,000 operations min. (under no load at 1,800 operations/h)
	Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h) *2
EMC	(EMI): EN61812-1
	Emission Enclosure: EN55011 Group 1 class A
	Emission AC Mains: EN55011 Group 1 class A
	(EMS): EN61812-1
	Immunity ESD: IEC61000-4-2: 6 kV contact discharge (level 3), 8 kV air discharge (level 3)
	Immunity RF-interference from AM Radio Waves: IEC61000-4-3: 10 V/m (80 MHz to 1 GHz) (level 3)
	Immunity RF-interference from Pulse-modulated Radio Waves: IEC61000-4-3: 10 V/m (900±5 MHz) (level 3)
	Immunity Conducted Disturbance: IEC61000-4-6: 10 V (0.15 to 80 MHz) (level 3)
	Immunity Burst: IEC61000-4-4: 2 kV power-line (level 3), 2 kV I/O signal-line (level 4)
	Immunity Surge: IEC61000-4-5: 1 kV line to line (level 3), 2 kV line to ground (level 3)
Case color	Light gray (Munsell 5Y7/1)
Degree of protection	IP40 (panel surface)
Weight	Approx. 90 g

*1.The value is ±5% FS +100 ms to −0 ms max. when the C, D, or G mode signal of the H3CR-AP is OFF.

*2.Refer to Data Sheet.

*3.Relay output only.