Delta Inverter VFD drive VFD004S43A 3Phase 380V 0.4KW 0.5HP 1~400Hz Inkle loom &Packaging machine

VFD004S43A

Features

General Purpose AC Micro Drive. Delta Electronics most cost effective general purpose drive. The VFD-S series drive is famous for its low-noise carrier frequency feature and easy to use keypad. 

Specifications

?Output frequency 1.0 ~ 400 Hz

?Adjustable V/f curve

?Carrier frequency up to 10 kHz

?Built-in PID feedback control

?Built-in MODBUS communication, baud rate up to 38400 bps

?Momentary power failure or fault restart

?Built-in Sleep / Revival function

?Support communication module (DN-02, LN-01, PD-01)

Applications

Air conditioner for large buildings; water supply system for large buildings; temperature control of middle/large oven; webbing loom; packing machine; conveyer belt; fan of drying machine, etc. 

General Specifications

Control Characteristics	Control System		SPWM (Sinusoidal Pulse Width Modulation)Control (V/f or sensorless vector control)
	Frequency Setting Resolution		0.01Hz
	Outing Frequency Resolution		0.01Hz
	Torque Characteristics		Including the auto-torque/auto-slip compensation; starting torque can be 150% at 5.0Hz
	Overload endurance		150% of rated current for 1 minute
	Skip Frequency		Three zones, setting range 0~400Hz
	Accel/Decel Time		0.1 to 600 seconds (2 Independent setting of Accel/Decel time)
	Stall Prevention Level Frequency Setting		20%-150%, Setting of Rated Current
	DC injection Braking		Operation frequency 0~400Hz, output 0~30% rated current Start time 0~60 seconds, stop time 0~60 seconds
	Braking Torque		Approx, 20% (up to 125% possible with optional braking resistor or externally mounted brake unit
	V/f Pattern		Adjustable V/f pattern
Operating Characteristics	Frequency Setting	Keypad	Setting by “UP” “Down”
		External Signal	Potentiometer-5k ohm / 0.5W, 0 to +10VDC, 4 to 20mA, RS-485 interface; Multi-function Inputs 0 to 5(7 steps, Jog, up/down)
	Operation Setting Signal	Keypad	Set by RUN and STOP
		External Signal	2 wires/3 wires (RUN,STOP,FWD/ REV), JOG operation, RS-485 serial interface(MODBUS)
	Multi-function Input signal		Multi-step selection 0 to 7, Jog, accel/decal inhibit, first to forth accel/decal switches, counter, PLC Operation external Base Block (NC,NO), axxiliary motor control is invalid, ACI/AVI/AUI selections, driver reset, UP/DOWN key setting, sink/source selection
	Multi-function Output Indication		AC drive operating, frequency attained, non-zero frequency, Base Block, fault indication, local/remote, indication, auxiliary motor output, drive is ready, overheat alarm, emergency stop
	Analog Output Signal		Analog frequency/current signal output
Alarm Output Contact			1 Form C contact or open collector output
Operation Functions			AVR, S-Curve, Over-Voltage, Over-Current Stall Prevention, Fault Records, Adjustable Carrier Frequency, DC Braking, Momentary Power Loss restart, Frequency Limits, Parameter Lock/Reset, Counter, PID Control, PLC, MODBUS Communication, Reverse Inhibition, Abnormal reset, abnormal re-start, digital frequency output, sleep/revival function,
Protection Functions			Self-testing, Over Voltage, Over Current, Under Voltage, Overload, Overheating, External Fault, Electronic thermal, Ground Fault
Display Keypad			6-key, 4-digit, 7-segment LED, 4 status LEDs, master frequency, output frequency, output current, custom units, parameter values for setup, review faults, RUN/STOP/RESET,FWD/REV
Built-in EMI Filter			VFD002S21E, VFD004S21E, VFD004S43E, VFD007S21E, VFD007S43E, VFD015S21E, VFD015S43E, VFD022S21E, VFD022S43E
Environmental Conditions	Enclosure Rating		IP20
	Pollution Degree		2
	Installation Location		Altitude 1,000m or lower, keep from corrosive gasses, liquid and dust
	Ambient Temperature		-100C to + 500C (400C for side-by-side mounting) Non-Condensing and not frozen
	Storage/Transportation Temperature		-200C + 600C
	Ambient Humidity		Below 90% RH (non-condensing)
	Vibration		9.80665m/s2(1G) less than 20Hz, 5.88m/s2 (0.6G) at 20 to 50Hz

Standard Specifications

115V series 1-phase

Model Number VFDXXXS		002	004	007
Max. Applicable Motor Output (kW)		0.2	0.4	0.75
Max. Applicable Motor Output(HP)		0.25	0.5	1.0
Output Rating	Rated Output Capacity(kVA)	0.6	1.0	1.6
	Rated Output Current(A)	1.6	2.5	4.2
	Maximum Output Voltage(V)	3-phase proportional to twice the input Voltage
	Output Frequency (Hz)	0.1~400Hz
	Carrier Frequency (kHz)	3-10
Input Rating	Rated Input Current(A)	Single Phase
		6	9	16
	Rated Voltage, Frequency	Single phase 100-120V, 50/60Hz
	Voltage Tolerance	+-10%(90~132V)
	Frequency Tolerance	+-5%(47~63Hz)
Cooling Method		Natural
Weight(kg)		1.3	1.5	2.0

230V Series 1-phase/3-phase

Model Number VFDxxxS21/23		002	004	007		015	022
Max. Applicable Motor Output (kW)		0.2	0.4	0.75		1.5	2.2
Max. Applicable Motor Output(HP)		0.25	0.5	1.0		2.0	3.0
Output Rating	Rated Output Capacity(kVA)	0.6	1.0	1.6		2.9	4.4/4 .2
	Rated Output Current(A)	1.6	2.5	4.2		7.5	11.0
	Maximum Output Current(V)	3-Phase Proportional to input voltage
	Output Frequency (Hz)	0.1~400Hz
	Carrier Frequency (kHz)	3-10
Input Rating	Rated Input Current(A)	Single/3-Phase
		4.9/1.9	6.5/2.7		9.7/5.1	15.7/9.0		24/15
	Single(3-phase Input Current)	1.6	3.0	5.1		8.4	--
	Rated Voltage, Frequency	Single/3-phase 200-240V,50/60Hz
Voltage Tolerance		+-10%(180~264V)
Frequency Tolerance		+-5%(47~63V)
Cooling Method		Natural				Fan cooled
Weight(kg)		1.3	1.5	1.5		2.2	3.2

460V Series 3-phase

Model Number VFDXXXS		004	007	015	022
Max. Applicable Motor Output(kW)		0.4	0.75	1.5	2.2
Max. Applicable Motor Output(HP)		0.5	1.0	2.0	3.0
Output Rating	Rated Output Capacity(kVA)	1.2	2.0	3.3	4.4
	Rated Output Current(A)	1.5	2.5	4.2	5.5
	Maximum Output Voltage(V)	3-Phase Proportional to input voltage
	Output Frequency(Hz)	0.1-400Hz
	Carrier Frequency(kHz)	3-10
Input Rating	Rated Input Current(A)	3-phase
		1.7	2.9	5.1	6.9
	Rated Voltage, Frequency	3-phase 380~480V, 50/60Hz
	Voltage Tolerance	+-10%(342~528V)
	Frequency Tolerance	+-5%(47~63Hz)
Cooling Method		Natural	Fan Cooled
Weight(kg)		1.5	1.5	2.0	2.2

Dimensions

 

Standard wiring diagram