No comment |
>
Motion Control System >
Servo system >
Kinco Servo Driver CD Series CD620-0188-0062-AA-000 1.26-1.88KW 1/3 Phase AC220V+/-20% 47~63Hz NewKinco Servo Driver CD Series CD620-0188-0062-AA-000 1.26-1.88KW 1/3 Phase AC220V+/-20% 47~63Hz New Free shippingIf you need more than 10pcs and want to get better wholesale price, please feel free to contact us by following:
email:[email protected]
Tel:0086-574- 88333153
We will quote you our best price to you in 24hours.
Specifications:
CD620
Main Supply Voltage: AC220V+/-20% 47~63Hz
Rated Output Power(KW): 1.26-1.88
Dimensions mm: 220X194.5X66
Model parameter
CD620-AA-000
Power
Main supply voltage
Single-phase or 3-phase AC220V±20% 47~63Hz
Control circuit voltage
DC24V 1A
Current
Rated current(RMS)
7A
Peak current(PEAK)
25A
Feedback signal
2500PPR (incremental encoder with 5V )
Brake chopper
Use an external braking resistor if necessary
Brake chopper threshold
DC680V±5V
Over-voltage alarming threshold
DC700V±5V
Under-voltage alarming threshold
DC400V±5V
Cooling method
Fan
Weight
2.4kg
Position
ModeMax. frequency of input pulse
Differential signal: 500KPPS, Open-collector signal: 200KPPS
Pulse command mode
Pulse+direction, CCW+CW, (higher voltages than 5V need external current limiting resistors)(do not support A+B phase)
Command smoothing
Low-pass filtering(Adjustable by internal parameters)
Feedforward gain
Adjustable by internal parameters
Electronic gear ratio
Setting range, Gear factor: -32768~32767, Gear divider: 1~32767, 1/50≤|Gear factor/Gear divider|≤50
Position loop sampling frequency
1KHz
Speed
ModeAnalog input voltage range
0 ~±10V(Resolution 12bit)
Input impedance
200K
Analog input sampling frequency
4KHz
Command source
External analog command/iAdjustable by internal parameters
Command smoothing
Low-pass filtering(Adjustable by internal parameters)
Input voltage dead-zone setting
Adjustable by internal parameters
Input voltage offset settiong
Adjustable by internal parameters
Speed limit
Adjustable by internal parameters
Torque limit
Adjustable by internal parameters / External analog command control
Speed loop sampling frequency
4KHz
Torque
ModeAnalog voltage input range
0 ~±10V (Resolution 12bit)
Input impedance
200K
Input sampling frequency
4KHz
Command source
External analog command/internal command
Command smoothing
Low-pass filtering(Adjustable by internal parameters)
Speed limit
Adjustable by internal parameters/External analog command control
Input voltage dead-zone setting
Adjustable by internal parameters
Input voltage offset setting
Adjustable by internal parameters
Current sampling frequency
16KHz
Digital
InputInput specification
7 digital inputs, with COM1 terminal for PNP or NPN connection.
Input function
Define freely according to requirement, supporting following functions: Driver enable,driver fault reset,driver mode control,Proportional control, forward inhibit limit, reverse inhibit limit, negative limit position,home signal, speed command reverse, internal speed or position select
Digital
OnputOutput specification
5 digital outputs,OUT1~OUT4 current is 100mA,OUT5 current is 800mA
Output function
Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, N signal
Protection functions
Over-voltage protection,under-voltage protection,motor over-heat protection(I²T),short-circuit protection,drive over-heat protection,etc.
Communication interface
RS232
Operation
EnvironmentOperating temperature
0~40 °C
Storage temperature
-10 °C ~70 °C
Humidity(non-condensing)
5~95%
Protection class
IP20
Installation environment
Installed in a dust-free,dry and lockable environment(such as in a electrical cabinet)
Installation mode
Vertical installation
Altitude
Below 1000m
Atmospheric pressure
86kpa~106kpa
No comment |