E6B2-CWZ6C 1500P/R encoder

E6B2-CWZ6C 1500P/R OMRON encoder

Incremental outer diameter φ40 encoder

 the generic type of φ40
? corresponds to the power supply voltage DC5 ~ 24V
(Open collector output)
? The outer diameter of φ40 equipped with the resolution of 2000P / R
? with the origin position Z is relatively simplistic display
? shaft load, radial 30N thrust to 20N
? attached to the reverse connection, load short-circuit protection circuit to improve the reliability
(Also available in the linear drive output)

 

Model		E6B2-CWZ6C	E6B2-CWZ5B	E6B2-CWZ3E	E6B2-CWZ1X
Project
Supply voltage		DC5V-5 ~ 24V +15% Less than 5% of the pulse (p-p)	DC12V-10% ~ 24V +15% Less than 5% of the pulse (p-p)	DC5V-12V to +10% Less than 5% of the pulse (p-p)	DC5V ± 5% Less than 5% of the pulse (p-p)
Current consumption * 1		70mA following	80mA following		130mA following
Resolution (pulses / rotation)		10?20?30?40?50?60? 100?200?300?360? 400?500?600?720? 800?1,000?1,024?1,200? 1,500?1,800?2,000	100?200?360?500? 600?1,000?2,000	10?20?30?40?50?60? 100?200?300?360? 400?500?600?1,000? 1,200?1,500?1,800?2,000	10?20?30?40?50?60? 100?200?300?360? 400?500?600?1,000? 1,024?1,200?1,500? 1,800?2,000
Output phase		A?B?Z Phase			A?A?B?B?Z?ZPhase
Output phase difference		Phase A, B, phase difference of 90 ± 45 ° C (1/4 ± 1/8T)
Output mode		NPN open collector output	PNP open collector output	Voltage output (NPN output)	Linear drive * 2
Output capacity		Below the applied voltage: DC30V Synchronous current: 35mA max. Residual voltage: 0.4V (At sink current of 35mA)	Below the applied voltage: DC30V Synchronous current: 35mA max. Residual voltage: 0.4V (At sink current of 35mA)	Output resistance: 2kΩ Synchronous current: 20mA max. Residual voltage: 0.4V (At sink current of 20mA)	AM26LS31 considerable product Output current H: IO =-20mA L-bit: IS = 20mA Output voltage VO = 2.5V VS = 0.5V below
The highest frequency response *3		100kHz	50kHz	100kHz
The output rise and fall time		1μs following Control the output voltage: 5V Load resistor 1kΩ Cable length 2m	1μs following (Cable length: 2m synchronous current: 10mA)		0.1μs following Cable length: 2m IO =-20mA, IS = 20mA
Starting torque		0.98mN·m following
Moment of inertia		1×10?6kg·m2 following
Shaft allows the force	Radial direction	30N
	Axial	20N
Allows the maximum speed		6,000r/min
Protection circuit		Load short-circuit protection, power supply reverse wiring protection
Ambient temperature range		Action: -10 ~ +70 ? save: -25 ~ +85? (with no icing)
Ambient humidity range		Action, save: 35 ~ 85% RH (no condensation)
Insulation resistance		20MΩ or more (500 VDC megger) charging the Ministry of the overall housing
Withstand Voltage		Voltage AC500V 50/60Hz 1min between charging and case
Vibration (durable)		10 ~ 500Hz complex amplitude of 2mm or 150 m/s2, X-, Y, Z each direction scan 11min 3 scan
The impact of (durable)		1,000 m/s2 X, Y,, and Z directions for three times
Protection structure * 3		Enclosure rating IEC IP50
Connection		Pre-wired (standard cable length 500mm)
Material shell	Shell	ABS
	Ministry of the base metal	Aluminum
	Axis	SUS420J2
Weight (packaged)		About 100g
Attachment		Coupling, hex wrench, manual

 

* 1 When power flows through the red flow of about 9A.(Time: about 0.3ms)
* The line driver output is based on the RS-422A data transmission circuit, through the double-stranded wire hunt for long-distance transmission. (Built-in AM26LS31 fairly products)
* 3. Electricity highest response speed according to the resolution and the highest response frequency requirements.

 

Therefore, when the rotation exceeds the maximum response speed, electrically can not trace the signal.