3PH 85mm NEMA34 4A 7.5NM 1071ozin 220VAC Stepper motor Drive kits 3S85Q-040F7+3M2280N

3PH 85mm NEMA34 4A 7.5NM 1071ozin 220VAC Stepper motor Drive kits  3S85Q-040F7+3M2280N

3S85Q-040F7+3M2280N

Hybrid Servo Motor 3S85Q-040F7

Specifications

Model	3S85Q-040F7
Step Angle	1.2centigrade degree±5%
Phase Current (A)	4
Holding Torque (Nm)	7.5
Damping Torque (Nm)	0.36
Winding Resistance (ohm)	1.78
Winding Inductance(mH)	17.1
Motor Inertia (Kg.com²)	0.44
Motor Length L(mm)	157±1
Number of Lead Wires	3
Insulation Class	B
Withstand Voltage Level	1800VAC,1S,5mA
Max.Axial Load (N)	60
Max.Readial Load (N)	220
Operating Temperature	-30centigrade degree~30centigrade degree
Surface Temperature Rise	Max.80centigrade degree(Rated Phase Current after Phases are Connected)
Insulation Impedance	Minimum 100Mohm,500VDC
Weight (Kg)	5.3

Hybrid Servo Drive 3M2280N

Features:

High Performance, Low Cost, and Diversified Functions

The Input Voltage of 3M2280N is 187V~253V.

Automatic Parameter Adjustable Regulation

Driver Test Running Function

Phase Memory Function

PLS+DIR and CW/CCW Control Signal Available.

Optocoupler Isolation I/O. There is an ERR Signal Output.

The Driver will Reduce the Phase Current of the Motor by a Half in 1.5 Seconds.

Opto-Isolation Signal Input, With Pulse Response Frequency up to 400 KHz

14 Micro-Step Value, the Maximum Micro-Step Value is 20000 Pulse/Rev.The Maximum Output Phase Current is 8A(Peak).

With the Protection Function of Over-Voltage, Under-Voltage, Over-Current, Overheat

With Step Smooth Filter,Can Smooth the Input Pulse,Reduce the Transient Motion of Motor,Make the Motor Runs More Smoothly.

Specification

Model					3M2280N
Parameter Lable
Input Voltage					3M2280N: Single-Phase 220V AC +/-15% (50Hz)(187VAC~253VAC)
Output Current					2.8, 3.2, 3.6, 4.0, 4.4, 4.8, 5.2, 5.6, 6, 6.4, 6.8, 7.2, 7.6 8.0
Micro Step					400, 500, 600, 800, 1000, 1200, 1500, 2000, 3000, 4000, 5000, 6000, 10000, 20000
Input Signal					Three Control Signal Ports: PLS(CW)/DIR(CCW)/FRE; Current Range: 6 ~16 mA
Control Signal Input Method					PLS+DIR; CW/CCW
Output Signal					ERR, Open Collector Output, Max Current: 10 mA.
Automatic Half-Current					The Driver Will Reduce the Phase Current of the Motor by a Half in 1.5 Seconds.
Protection					Over-Voltage, Under-Voltage, Short Circuit, and Overheat Protection
Absorbing Circuit*					Need Customize, Used to Absorb the Energy Feed Back by the Motor
Environment Parameter
Cooling Way					Forced Air Cooling
Environment		Operation Environment			Avoid the Environment with Great Amount of Metallic Powder, Oil mist, or Erosive Gases.
		Operation Humidity			<85%, RH (Non-Condensing or Water Drops)
		Operation Temperature			0centigrade degree ~ +40centigrade degree
		Storage Temperature			-20centigrade degree ~ +70centigrade degree
Weight					1.5Kg
Dimensions					201mm×147mm×66mm
Protect Level					IP20
Function of Rotary Switch
S1,Micro-Step:
S1	0		1	2		3	4	5	6	7
Pulse/rev	400		500	600		800	1000	1200	1500	2000
S1	8		9	A		B	C	D	E	F
Pulse/rev	3000		4000	5000		6000	10000	20000	SET1	SET2
S2,Current:
Mode	PLS+DIR
S2	0		1	2		3	4	5	6	7
Peak(A)	2.8		3.2	3.6		4	4.4	4.8	5.2	5.6
Rms(A)	1.98		2.26	2.55		2.83	3.11	3.39	3.68	3.96
Mode	CW/CCW
S2	8		9	A		B	C	D	E	F
Peak(A)	6		6.4	6.8		7.2	7.6	8	M1	M2
Rms(A)	4.24		4.53	4.81		5.09	5.37	5.66