AC220V 200W 1.6A 0.64NM 3Krpm 60mm AC Servo Motor Drive kits SMH60S-0020-30AAK-3LKH+ED430-0020-PA-K-000 with 3M cable

AC220V 200W 1.6A 0.64NM 3Krpm 60mm AC Servo Motor Drive kits SMH60S-0020-30AAK-3LKH+ED430-0020-PA-K-000 with 3M cable

Motor + Drive: SMH60S-0020-30AAK-3LKH+ED430-0020-PA-K-000

1 Motor Specifications

Motor series		Small inertia, flange size 60mm
Model		SMH60S-0020-30AAK-3LKH
DC link voltage UDC		300
Continuous performance	Rated power PN (W)	200
	Rated torque TN (Nm)	0.64
	Rated speed  nN (rpm)	3000
	Rated current IN (A)	1.6
Maximum torque       Tm (Nm)		1.92
Maximum current     Im (A)		4.8
Standstill torque   TS (Nm)		0.7
Standstill current     IS (A)		1.79
Resistance line-line   RL (ohm)		8.02
Inductance line-line   LL (mH)		16.3
Electrical time constant τe (ms)		2.03
Mechanical time constant τm (ms)		2.26
Reverse voltage constant Ke (V/krpm)		29
Torque constant   Kt (Nm/A)		0.48
Rotor moment of inertia Jm (Kg·cm² )		0.375
Pole pair number		3
Maximum voltage rising du/dt (KV/μs)		8
Insulation class		F
Maximum radial force   F (N)		180
Maximum axial force   F (N)		90
Weight   G(Kg)		1.3
Length of motor  L(mm)		120
Position feedback device		Incremental encoder 2500ppr
Cooling method		Totally enclosed, non-ventilated
Protection level		IP65 for body, shaft sealing IP54
Environmental  conditions for  operation	Temperature	-20centigrade degree~40centigrade degree
	Humidity	Below 90% RH (No condensing)
	Ambient enviroment	Away from active gas, combustible gas, oil drops and dust
	Altitude	Maximum altitude 4000m, Rated power at 1000m or below, Above 1000m: Decreasing 1.5% per 100m rise

2 Drive Specifications

Model	ED430
	ED430-0020-PA-K-000
Main Supply Voltage	Single-Phase AC220V±15%
Rated Power Frequency	50Hz~60Hz
Control Power Supply	DC24±10% , 2A
Digital Signal Input	DC24±10%, 10mA
Digital Signal Output	DC24±10%, 0.5A
Analog Signal Input	-10V~+10V
Rated Output Power(KW)	0.2
Energy-Consumed Braking	If the system generates an over-voltage alarm when it starts or stops sharply, add an external braking resistor to absorb the feedback energy of the motor, the minimum resistance for ED430 Series is 27W
Energy-Consumed Braking Voltage	DC385±5V
Over-Voltage Alarm Voltage	DC400±5V
Under-Voltage Alarm Voltage	DC210±5V
Dimensions mm (H×W×D)	265X165X62
Weight	1.9Kg
Operating Temperature	0~40centigrade degree
Storage Temperature	-10~70centigrade degree
Humidity	5~85%
Contamination Level	2
Protection Level	IP20
Installation Environment	Installed in a Dust-Free, Dry, and Lockable Environment (in a Electrical Cabinet, for Example)
Installation Mode	Vertical Installation
Installation Altitude	No Power Limit Under 1000m
Pressure	86~106Kpa
Internal Programmable	An Internal Space of 16.5 KB is Provided for 256 Sequences, Which can Save a Controller on Some Occasions
External I/O	3 External Digital Outputs (24V,0.5A),the Target Position to Output or Alarm Output Function can be Implemented by Internal Programming
	8 External Digital Inputs, Supporting Internal Sequence Calling Via the Input Interface and Positioning Function
	(Input Delay: About 1 ms; Input Current: About 4 mA)
Analog Input	One Differential Analog Input, Implementing Control Over Motor Speed and Position by Analog Input; Input Voltage Range ± 10V, Input Delay: About 0.1 ms
Analog Output	Two Independent Analog Outputs, Capable of Monitoring the Change of Internal Object
Comparator	Four Internal Comparators, With the Comparison Results to be Used to Trigger Program Sequences
Timer	Supporting the Function of Triggering Sequences by Timer or Events
Counter	Four Groups of Internal Counters, Which can be Set to Trigger Sequences
Calculator	An Internal Calculator can be Used for Data Duplication, Addition, Subtraction, Multiplication, and Division, and Logic Operation
Internal Oscilloscope	The ECO2WIN Software Enables a User to Monitor Operation Parameters Such as Speed, Position and Current on a PC
Encoder Signal Output Function	In a Master/Slave Control Mode, the Motor Encoder Signal or Master Encoder Signal can be the Input for the Slave Signal Encoder, With a Maximum Output Frequency of 2 MHz
Master Encoder Signal Input Function	Programmable to be Pulse/Direction Signal Control, CW/CCWW Control, Electronic Gear or electronic cam control (5V signal), with a maximum input frequency of 2 MHz
Feedback Signal	Incremental A, B, Z , /A, /B, /Z Signal
RS232	9.6K Baud Rate, Supporting a Maximum of 15 Sites, and Supporting Direct Communication with a PC with the ECO2WIN Software, or Direct Communication with an eView Touch Screen or Text
RS485	38.4K Baud Rate, Supporting a Maximum of 15 Sites, and Communication Cables with a Length up to 400M
CAN BUS	Maximum Baud Rate of 1M, and Supporting a Maximum of 127 Sites
PROFIBUS DP	Maximum Baud Rate of 12M, and Supporting a Maximum of 127 Sites