AC220V 750W 3.9A 2.39NM 3Krpm 80mm AC Servo Motor Drive Kit SMH80S-0075-30AAK-3LKH+CD422-AA-000 with 3M cable

 AC220V 750W 3.9A 2.39NM 3Krpm 80mm AC Servo Motor Drive Kit SMH80S-0075-30AAK-3LKH+CD422-AA-000 with 3M cable

Motor + Drive: SMH80S-0075-30AAK-3LKH+CD422-AA-000

1 Motor Specifications

Motor series		Small inertia, flange size 80mm
Model		SMH80S-0075-30AAK-3LKH
DC link voltage UDC		300
Continuous  performance	Rated power   PN (W)	750
	Rated torque   TN (Nm)	2.39
	Rated speed   nN (rpm)	3000
	Rated current IN (A)	3.9
Maximum torque         Tm (Nm)		7.17
Maximum current        Im (A)		11.7
Standstill torque      TS (Nm)		2.63
Standstill current     IS (A)		4.4
Resistance line-line   RL (Ω)		1.4
Inductance line-line   LL (mH)		7.5
Electrical time constant τe (ms)		5.35
Mechanical time constant τm (ms)		0.75
Reverse voltage constant Ke (V/krpm)		40
Torque constant           Kt (Nm/A)		0.662
Rotor moment of inertia   Jm (Kg·cm² )		1.36
Pole pair number		3
Maximum voltage rising du/dt (KV/μs)		8
Insulation class		F
Maximum radial force    F (N)		335
Maximum axial force  F (N)		167.5
Weight  G(Kg)		3.3
Length of motor L(mm)		147
Position feedback device		Incremental encoder 2500ppr
Cooling method		Totally enclosed, non-ventilated
Protection level		IP65 for body, shaft sealing IP54
Environmental  conditions for  operation	Temperature	-20centigrade degree~40centigrade degree
	Humidity	Below 90% RH (No condensing)
	Ambient enviroment	Away from active gas, combustible gas, oil drops and dust
	Altitude	Maximum altitude 4000m, Rated power at 1000m or below, Above 1000m: Decreasing 1.5% per 100m rise

2 Drive Specifications

Model parameter				CD422-AA-000
Power		Main supply voltage		1phase AC220V -20/+15% 47~63Hz
		Control circuit voltage		18VDC~30VDC 1A
Current		Rated current(RMS)		4A
		Peak current(PEAK)		15A
Feedback signal				2500PPR (incremental encoder with 5V supply)
Brake chopper				Use an external braking resistor according to application, mainly in occasion of quick stop.
Brake chopper threshold				DC380V±5V
Over-voltage alarming threshold				DC400V±5V
Under-voltage alarming threshold				DC200V±5V
Cooling method				Natural air cooling
Weight				1.2kg
Position Mode	Max. frequency of input pulse			Differential signal: 500KPPS, Open-collector signal: 200KPPS
	Pulse command mode			Pulse+direction, CCW+CW, A+B phase (5V-24V)
	Command smoothing			Low-pass filtering(Internal parameters)
	Feedforward gain			Internal parameters
	Electronic gear ratio			Setting range, Gear factor: -32768~32767, Gear divider: 1~32767, 1/50≤|Gear factor/Gear divider|≤50
	Position loop sampling frequency			1KHz
Speed Mode	Analog input voltage range			-10 ~+10V(Resolution 12bit)
	Input impedance			200K
	Analog input sampling frequency			4KHz
	Command source			External analog command/internal command
	Command smoothing			Low-pass filtering(Internal parameters)
	Input voltage dead-zone setting			Internal parameters
	Input voltage offset setting			Internal parameters
	Speed limit			Internal parameters
	Torque limit			Internal parameters / External analog command control
	Speed loop sampling frequency			4KHz
Torque Mode	Analog voltage input range			-10 ~+10V (Resolution 12bit)
	Input impedance			200K
	Input sampling frequency			4KHz
	Command source			External analog command/internal command
	Command smoothing			Low-pass filtering(Internal parameters)
	Speed limit			Internal parameters /External analog command control
	Input voltage dead-zone setting			Internal parameters
	Input voltage offset setting			Internal parameters
	Current sampling frequency			16KHz
Digital Input	Input specification			7 digital inputs, with COMI terminal for PNP (high level valid 12.5-30V)or NPN (low level valid) connection.
	Input function			Define freely according to requirement, supporting following functions: Driver enable, driver fault reset, driver mode control, proportional control, positive limit, negative limit, homing signal, reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain
Digital Onput	Output specification			5 digital outputs,OUT1 - OUT4 current is 100mA, BR+/BR- (Brake control output ) current is 500mA, can drive brake device directly
	Output function			Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, N signal, maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached
Protection functions				Over-voltage protection, under-voltage protection, motor over-heat protection(I²T),short-circuit protection, drive over-heat protection,etc.
Communication interface				RS232 (Connections with PC: 2-2, 3-3, 5-5)
Operation Environment			Operating temperature	0 - 40centigrade degree
			Storage temperature	-10centigrade degree - 70centigrade degree
			Humidity(non-condensing)	Below 90%RH
			Protection class	IP20
			Installation environment	Installed in a dust-free, dry and lockable environment(such as in a electrical cabinet)
			Installation mode	Vertical installation
			Height	No power limitation below 1000m
			Atmospheric pressure	86kpa~106kpa