E2E-X7D1S-Z Proximity Switch NEW

E2E-X7D1S-Z OMRON Proximity Switch NEW

Product Description:

Standard Sensors for detecting ferrous metals.

Wide array of variations. Ideal for a variety of applications.

Models with different frequencies are also available to prevent mutual interference.

Superior environment resistance with standard cable made of oilresistant PVC and sensing surface made of material that resists cutting oil.

Specifications:

Size		M8		M12		M18		M30
Shielded		Shielded	Unshielded	Shielded	Unshielded	Shielded	Unshielded	Shielded	Unshielded
Model		E2E-	E2E-	E2E-	E2E-	E2E-	E2E-	E2E-	E2E-
		X2D[]	X4MD[]	X3D[]	X8MD[]	X7D[]	X14MD[]	X10D[]	X20MD[]
Sensing distance		2 mm ±10%	4 mm ±10%	3 mm ±10%	8 mm ±10%	7 mm ±10%	14 mm ±10%	10 mm ±10%	20 mm ±10%
Set distance *1		0 to 1.6 mm	0 to 3.2 mm	0 to 2.4 mm	0 to 6.4 mm	0 to 5.6 mm	0 to 11.2 mm	0 to 8 mm	0 to 16 mm
Differential travel		15% max. of sensing distance		10% max. of sensing distance
Detectable object		Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Data Sheet.)
Standard sensing		Iron, 8 ×	Iron, 20 ×	Iron, 12 ×	Iron, 30 ×	Iron, 18 ×	Iron, 30 × 30 × 1 mm		Iron, 54 ×
object		8 × 1 mm	20 × 1 mm	12 × 1 mm	30 × 1 mm	18 × 1 mm			54 × 1 mm
Response frequency		1.5 kHz	1 kHz		0.8 kHz	0.5 kHz	0.4 kHz		0.1 kHz
*2
Power supply voltage		12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
(operating voltage
range)
Leakage current		0.8 mA max.
Control	Load	3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models
output	current
	Residual	3 V max. (Load current: 100 mA, Cable length: 2 m, M1J-T Models only: 5 V max.)
	voltage
	*3
Indicators		D1 Models: Operation indicator (red) and setting indicator (green)
		D2 Models: Operation indicator (red)
Operation mode		D1 Models: NO
(with sensing object		D2 Models: NC
approaching)		Refer to Data Sheet.
Diagnostic output		0.3 to 1 s
delay
Protection circuits		Surge suppressor, Load short-circuit protection (for control and diagnostic output)
Ambient		Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
temperature range
Ambient		Operating/storage: 35% to 95% (with no condensation)
humidity range
Temperature		±15% max. of sensing		±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
influence		distance at 23°C in the
		temperature range of -25
		to 70°C
Voltage influence		±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance		50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength		1000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance		Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance		Destruction: 500 m/s2		Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
		10 times each in X, Y, and
		Z directions
Degree of protection		Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
		Connector Models: IEC 60529 IP67
Connection method		Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired Connector Models (Standard cable length: 0.3 m)
Weight	Pre-wired	Approx. 60 g		Approx. 70 g		Approx. 130 g		Approx. 175 g
(packed	Models
state)	Pre-wired	---		Approx. 40 g		Approx. 70 g		Approx. 110 g
	Connector
	Models
	Connector	Approx. 15 g		Approx. 25 g		Approx. 40 g		Approx. 90 g
	Models
Materi-	Case	Stainless steel (SUS303)		Nickel-plated brass
als	Sensing	PBT
	surface
	Clamping	Nickel-plated brass
	nuts
	Toothed	Zinc-plated iron
	washer
Accessories		Instruction manual

*1.Use the E2E within the range in which the setting indicator (green LED) is ON (except D2 Models).

*2.The response frequency is an average value.

Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.

*3.The residual voltage of each M1J-T Model is 5 V. When connecting to a device, make sure that the device can withstand the residual voltage. (Refer to Data Sheet for details.)