| No comment |
Your Position: Home
> Control System > PLC > Siemens PLC > 6ES7132-1BH00-0XB0 SIEMENS ELECTRONIC MODULE FOR ET 200L New6ES7132-1BH00-0XB0 SIEMENS ELECTRONIC MODULE FOR ET 200L New
Description
6ES7132-1BH00-0XB0 SIEMENS ELECTRONIC MODULE FOR ET 200L New
SIEMENS ELECTRONIC MODULE FOR ET 200L 6ES7132-1BH00-0XB0
Product Description:
SIMATIC DP, ELECTRONIC BLOCK FOR ET 200L, 16 DO, 24V DC/0.5A.
Features:
General information | |
Vendor identification (VendorID) | 0016h |
Supply voltage | |
24 V DC | Yes |
Reverse polarity protection | Yes |
Mains buffering | |
Mains buffering, min. | 20 ms |
Load voltage 2L+ | |
Rated value (DC) | 24 V; 1L+, 2L+, 3L+ |
Input current | |
from load voltage L1 (without load), max. | 50 mA; Per load group (L1+ or L2+ / L3+) |
from supply voltage L+, max. | 70 mA; L4+ / L5+ |
Power losses | |
Power loss, typ. | 5 W |
Hardware configuration | |
Rack | |
Required terminal block | TB 16L |
Digital outputs | |
Number/binary outputs | 16 |
Functionality/short-circuit strength | Yes; Electronic |
Response threshold, typ. | 0.7 A |
Limitation of inductive shutdown voltage to | Typ. (L1+ or L2+ / L3+) -55 V |
Lamp load, max. | 5 W |
Controlling a digital input | Yes |
Load resistance range | |
lower limit | 41 Ω |
upper limit | 28000 Ω |
Output voltage | |
Rated value (DC) | 24 V |
for signal "1", min. | Ua - 3 V |
Output current | |
for signal "1" rated value | 0.5 A |
for signal "1" permissible range for 0 to 60 °C, max. | 0.5 A |
for signal "0" residual current, max. | 1 mA |
Output delay with resistive load | |
0 to | 50 ms |
1 to | 200 ms |
Parallel switching of 2 outputs | |
for increased power | No |
for redundant control of a load | Yes; only outputs of the same group |
Switching frequency | |
with resistive load, max. | 100 Hz |
with inductive load, max. | 0.5 Hz |
on lamp load, max. | 8 Hz |
Aggregate current of outputs (per group) | |
all mounting positions | |
up to 60 °C, max. | 4 A |
all other mounting positions | |
up to 40 °C, max. | 2 A |
Cable length | |
Cable length, shielded, max. | 1000 m |
Cable length unshielded, max. | 600 m |
Interfaces | |
PROFIBUS DP | |
Transmission rate, max. | 1.5 Mbit/s |
SYNC capability | Yes |
Direct data exchange (slave-to-slave communication) | Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC) |
Communication functions | |
Bus protocol/transmission protocol | PROFIBUS DP |
Interrupts/diagnostics/status information | |
Alarms | |
Alarms | No |
Diagnostic messages | |
Diagnostic functions | Yes |
Diagnostics indication LED | |
Bus fault BF (red) | Yes |
Status indicator digital output (green) | Yes |
Status indicator digital input (green) | Yes |
Monitoring 24 V voltage supply ON (green) | Yes |
Galvanic isolation | |
between PROFIBUS DP and all other circuit components | Yes |
Galvanic isolation digital outputs | |
between the channels | No |
between the channels and PROFIBUS DP | Yes; Optocoupler |
Isolation | |
Isolation checked with | 500 V DC |
Degree and class of protection | |
IP20 | Yes |
Ambient conditions | |
Operating temperature | |
horizontal installation, min. | 0 °C |
horizontal installation, max. | 60 °C; 40°C for other mountings |
Air pressure | |
permissible range, min. | 795 hPa |
permissible range, max. | 1080 hPa |
Relative humidity | |
Operation, min. | 5 % |
Operation, max. | 95 %; RH class 2 in accordance with IEC 1131-2 |
Vibrations | |
Operation, checked according to IEC 60068-2-6 | Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g) |
Shock test | |
checked according to IEC 60068-2-27 | Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms |
Connection method | |
Inputs/outputs | Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection |
Dimensions | |
Width | 145 mm |
Height | 60 mm |
Depth | 60.5 mm |
Weight | |
Weight, approx. | 130 g |
6ES7132-1BH00-0XB0 SIEMENS ELECTRONIC MODULE FOR ET 200L NewSIEMENS ELECTRONIC MODULE FOR ET 200L 6ES7132-1BH00-0XB0
Product Description:
SIMATIC DP, ELECTRONIC BLOCK FOR ET 200L, 16 DO, 24V DC/0.5A.
Features:
General information
Vendor identification (VendorID)
0016h
Supply voltage
24 V DC
Yes
Reverse polarity protection
Yes
Mains buffering
Mains buffering, min.
20 ms
Load voltage 2L+
Rated value (DC)
24 V; 1L+, 2L+, 3L+
Input current
from load voltage L1 (without load), max.
50 mA; Per load group (L1+ or L2+ / L3+)
from supply voltage L+, max.
70 mA; L4+ / L5+
Power losses
Power loss, typ.
5 W
Hardware configuration
Rack
Required terminal block
TB 16L
Digital outputs
Number/binary outputs
16
Functionality/short-circuit strength
Yes; Electronic
Response threshold, typ.
0.7 A
Limitation of inductive shutdown voltage to
Typ. (L1+ or L2+ / L3+) -55 V
Lamp load, max.
5 W
Controlling a digital input
Yes
Load resistance range
lower limit
41 Ω
upper limit
28000 Ω
Output voltage
Rated value (DC)
24 V
for signal "1", min.
Ua - 3 V
Output current
for signal "1" rated value
0.5 A
for signal "1" permissible range for 0 to 60 °C, max.
0.5 A
for signal "0" residual current, max.
1 mA
Output delay with resistive load
0 to
50 ms
1 to
200 ms
Parallel switching of 2 outputs
for increased power
No
for redundant control of a load
Yes; only outputs of the same group
Switching frequency
with resistive load, max.
100 Hz
with inductive load, max.
0.5 Hz
on lamp load, max.
8 Hz
Aggregate current of outputs (per group)
all mounting positions
up to 60 °C, max.
4 A
all other mounting positions
up to 40 °C, max.
2 A
Cable length
Cable length, shielded, max.
1000 m
Cable length unshielded, max.
600 m
Interfaces
PROFIBUS DP
Transmission rate, max.
1.5 Mbit/s
SYNC capability
Yes
Direct data exchange (slave-to-slave communication)
Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)
Communication functions
Bus protocol/transmission protocol
PROFIBUS DP
Interrupts/diagnostics/status information
Alarms
Alarms
No
Diagnostic messages
Diagnostic functions
Yes
Diagnostics indication LED
Bus fault BF (red)
Yes
Status indicator digital output (green)
Yes
Status indicator digital input (green)
Yes
Monitoring 24 V voltage supply ON (green)
Yes
Galvanic isolation
between PROFIBUS DP and all other circuit components
Yes
Galvanic isolation digital outputs
between the channels
No
between the channels and PROFIBUS DP
Yes; Optocoupler
Isolation
Isolation checked with
500 V DC
Degree and class of protection
IP20
Yes
Ambient conditions
Operating temperature
horizontal installation, min.
0 °C
horizontal installation, max.
60 °C; 40°C for other mountings
Air pressure
permissible range, min.
795 hPa
permissible range, max.
1080 hPa
Relative humidity
Operation, min.
5 %
Operation, max.
95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6
Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27
Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Connection method
Inputs/outputs
Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection
Dimensions
Width
145 mm
Height
60 mm
Depth
60.5 mm
Weight
Weight, approx.
130 g
